Getting Started with Plumbing Basics for Bathtub Installation
Getting Started with Plumbing Basics for Bathtub Installation
Blog Article
How do you really feel in relation to A Step-by-Step Guide to Installing a Bathtub?
Mounting a tub isn't exactly brain surgery, however it does need solid plumbing, woodworking, and often, tiling skills. Replacing an old bathtub with a new one is also a reasonably hard job. If the old tub is easily easily accessible, the project can relocate immediately; if you have to open up a wall surface to eliminate the old tub and place the new bath tub, the task is a lot harder. In either instance, the job is within a house handyman's skills, although you will need an assistant to vacate the old bathtub as well as embeded in the new one. See to it you have actually certified yourself for the job and fit attempting it. Instead of hiring a professional to take over a halfway-completed task, it is much better to think about using one before you begin. Chances are you might require an expert plumber to make tube connections.
This short article will aid you mount a new bathtub in your bathroom if you have actually already purchased a brand-new tub and do not need to change the setup of your previous water system pipes.
Your devices as well as material list need to comprise the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your setup, then the first thing you should do is disconnect the water. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The process of removing the existing taps can be rather troublesome as a result of the limited gain access to that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth all set for the remaining water that will originate from the pipelines. When the supply pipelines have been removed, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to going on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in location between the faucet and the sink. Safeguard the tap in place with the manufacturer supplied backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular faucet connectors. The previous type needs to be linked to the tap ends first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Tub
Making use of both wood boards under its feet, position the bathtub in the required position. The wooden boards are practical in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be achieved by checking the level and also changing the feet on the tub until the level checks out level.
To set up faucets, fit all-time low of the outermost flexible tap port to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the supply of water as well as inspect all joints and new pipework for leakages as well as tighten them if necessary. Fill up the bathtub and additionally examine the overflow outlet and also the regular outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bathtub ought to wait up until the tub has actually been made use of at least once as this will settle it into its final setting.
Getting ready for the Installment
Firstly, the sustaining frame supplied with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to stop stress on the bath tub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be suited its final setting.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to break a rigid seal, triggering the water to penetrate the wall surface between the bathroom and also the tiling, causing complications with moisture and also possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your components and fittings. They are offered in tubes and also cartridges, and also are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched newspaper or soft rope. Remember to constantly load the bath tub with water before sealing, to allow for the activity experienced when the bathtub is in usage. The sealer can fracture rather early if you do not take into account this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly offered on the market. It is suggested to fit the tiles making use of water-resistant or waterproof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a reader about How to Install a Bathtub, I figured sharing that excerpt was sensible. Liked our piece? Please share it. Let someone else check it out. We appreciate reading our article about How to Install a Bathtub.
Book An Estimate Now Report this page